CODE Error LASERJET 4 MPLUS

Error 02 Warming up
• Turn printer off. Unplug I/O cable from rear of printer. Power up printer and see if it goes to ready. If printer goes to ready, the problem could be a driver issue, a bad I/O port in the computer or a bad I/O cable. If the printer still stays in 02 warm up, replace the formatter board.
Error 11 Paper Out
• Check paper tray for paper. Make sure it is seated properly.
• Check the tray size actuating tabs on the paper tray for damage. Check to see if the actuators they contact aren't bent. The micro-switches they actuate could be defective or misaligned. Manually depress the actuators and listen for a click.
• Check that the paper sensor arm isn't stuck or broken.
• Paper Control Sensor PCA is defective.
Error 12 Printer Open no EP cartridge
• Check that the toner cartridge is installed.
• Check that the top cover is firmly closed.
• On HP II/IID/III/IIID printers this error is usually caused by a bad DC power supply.
• On HP IIP/IIP+/IIIP printers the primary cause is the density density adjusting. There is a slight possibility of it being a bad fan. There is also a slight possibility of the tab on the fuser access door above the MP tray breaking off and causing the error. If the fan starts to run, quits and you notice a burning odor, the scanner motor has failed and needs to be replaced. The problem can also be caused by a defective drum shutter on the toner cartridge.
• On the 4/4M/4+/4M+ the tab on the top cover that actuates the door interlock could be broken.
Error 13 Paper Jam
• Paper jams can occur in 3 places: Entry, registration and exit.
• If the paper isn't picking up out of the paper tray, visually inspect the pickup roller. If it looks shiny, replace it. You should also replace the separation pad as they work together. On the 4L/4P/5P/6P the pickup roller has a plastic shaft that breaks. You'll have to replace the whole pickup assembly. This requires major disassembly of the printer. Check our printer repair kits for your model printer. If you don't see it listed, email us.
• If you have an HP 4/4+/5 with an optional 500 sheet feeder that's jamming, check the balance knob adjustment. Center it with a full ream of paper for proper operation.
• If the paper is jamming at registration or anywhere between pickup and exit it could be a number of things. Check the paper path for torn bits of paper or label residue. On the II/III series, remove the metal registration guide plate (2 screws) and check underneath it. If the pickup rollers are moderately worn, the paper will stop just short of the registration roller. On the 4L/4P/5P/6P remove the screw holding the oblique roller assembly (Inside front of printer) and pull out and inspect the assembly and the area under it. On the HP 4/4+/5 pivot up the metal plate and check underneath it. Check the roller assembly on the left side for torn scraps of paper (a flashlight or torch is necessary).
• Make sure paper cassettes are firmly seated, corner tabs aren't bent. Some trays have lifting springs that could pop out if tray has been dropped.
• On HP IIP/IIP+/IIIP printers if the paper scrunches up at the toner cartridge you'll need our Inside Accordion Jam Repair Kit.
• Check your software settings in the program you are attempting to print from. Do you have the correct paper size specified? If you have a different paper size than what is in the tray, you'll get a paper jam.
• Exit jams are frequently caused by exit sensors. These sensors are typically mounted on the fuser assembly or adjacent to it. They are plastic arms that block and unblock an optical sensor. The arms can get stuck or knocked out of place when clearing paper jams. The optical sensors can also get dirt blocking the photo cell. Clean the sensor and check for free movement and proper installation of the sensor arms.
• On HP II/III series exit jams are mostly caused by worn gears. The best way to troubleshoot this is to defeat the door interlock. Press down on the arm on the top right of the fuser. Initiate a test page. While holding down the arm, press one of the metal cartridge detect switches just below the door interlock. Watch the movement of the gears. You will get a 51 error because the door is open. Recycle power to get rid of error. There is an arm gear on the lower right of the fuser that can shed teeth. There is also a 14 tooth gear below the large gear on top of the fuser. You can also manually rotate the large gear and check for binding or crunching. If that happens, then replace the 14 tooth gear. On the door, there are some delivery coupler gears that mate with the fuser and drive the exit roller. Check the gears for excessive wear. Replace if necessary. If the paper gets almost all the way out and jams, replace the exit roller or the exit roller assembly. If the error occurs after fuser replacement, check and see if the connector on the left of the fuser is properly mated with the one in the printer.
• On HP IIP/IIP+/IIIP printers if the paper has accordion folds on the bottom and jams on exit, order our Top Output Accordion Jam Repair Kit.
• On HP 4/4+/5 printers the most common cause of exit jams is the exit assembly. Order our 4/4+/5 Exit Jam Repair Kit. Exit jams in the fuser can be caused by a broken fuser drive gear or a broken gear on the fuser. Remove the fuser and check the gear inside the printer for broken teeth. Manually turn the gears on the fuser and check for smooth operation. Check the paper exit sensor arm for proper mounting and free movement.
• Check to make sure the rear door is closed on the printer. Open doors can cause 13 paper jam indications.
• On the 5L/6L check the registration sensor arm below the pickup roller. Also check the exit sensor arm (bottom center of the fuser). These arms frequently get stuck or dislodged clearing paper jams. On these printers, if you are experiencing frequent paper jams, order our 5L/6L Multi-Sheet/No Feed Repair Kit
Error 14 No EP cartridge
• Check that a toner cartridge is installed and fully seated.
• On HP II/III and IISi/4Si models check that at least one sensitivity tab is installed on the right side of the toner cartridge. If you see 2 holes and no square plastic tabs sticking in at least one of them, the printer will not see the cartridge. If one tab is installed and the printer still doesn't recognize the cartridge, try popping out the tab and putting it in the other position.
• On HP 4/4+/5 printers the high voltage contacts can be dirty or misaligned. If contacts are ok, replace the high voltage power supply.
Error 16 Toner low
• Toner cartridge is low on toner. Try gently rocking the cartridge to redistribute the toner. This will buy you 50-100 pages. Get a new cartridge as soon as possible.
• Dirty or misaligned contacts on the high voltage power supply.
• On the HP II/III printers it can be a loose connector on DC controller see tweaking for instructions on how to repair it.
• On the HP 4/4+/5 printers there is a potentiometer adjustment on the left side of the printer. You have to remove the left panel and you'll see it. It's located at about the exact center of the printer.
Error 18 MIO Not Ready
• The printer is not connected to a Lan.
• The MIO (Jet Direct) card is defective or not seated correctly. Reseat or replace it. If you have another printer with the same card, try swapping them. Always turn printer power off when removing or inserting cards.




Error 20 Memory Overflow
• Print job has exceeded the memory capacity of the printer. Simplify the print job, reduce the dpi setting or install additional memory. See our specials page for memory.
Error 21 Print Overrun
• See error 20
Error 22 I/O Configuration
• Printer or computer I/O configuration is incorrect
• I/O cable is wrong or damaged
• The computer is switched off
• I/O port on printer is damaged. Replace the formatter.
Error 23 I/O Not Ready
• I/O card can't accept data or isn't connected to the network. Check card seating (with power off) and replace if necessary.
Error 24 Job Memory Full
• Too much data or too complex data for printer memory. See error 20.
Error 25 XXX Memory Full
• Too much data or too complex data for printer memory. See error 20.
Error 30 PS Error 16
• I/O time out. Printer got tired of waiting for user interaction like a manual feed. Check the I/O connections. Check display panel for media request.
Error 30 PS Error 22/25
• Postscript error. Replace the Postscript SIMM module
Error 30 PS Error (all others)
• A PCL file was sent to the printer while it was in Postscript mode.
Error 30.1.1 Disk Failure
• 5si/8000 optional hard drive has crashed. Press select to continue.
Error 40 Data Transfer Error
• Printer and computer may be set to different baud rates.
• The computer is turned off.
• The MIO card is defective or improperly seated.
• Press continue or go on the printer to clear message.
Error 41 (temporary print engine error)
• Temporary error has occurred. Press Go or Continue. Power cycle the printer.
• On IIP/IIP+/IIIP with lower cassette option order our 41 Service Error Repair Kit
Error 41.1 41.2 41.3
• Defective connections. Reseat J205,206,207 and laser scanner connectors.
• Paper multifeed or wrong size paper being used.
• Paper size selection doesn't match the paper being used.
• Cassette is overfull or improperly adjusted.
Error 41.4 or 41.5
• Formatter PCA or DC controller is defective.
Error 50 (fuser malfunction)
• HP II/III series most likely cause is the ac power module is defective. Order the HP II/III Service 50 Error Repair Kit. If the quartz fuser lamp is burned out, order the replacement fuser on specials page. Slight possibility of loose connector on DC controller. See tweaking page DC controller could also be defective, but this is very rare.
• HP IIP/IIP+/IIIP most likely cause is burned out quartz lamp. Order the HP IIP/IIIP 50 Service Error Repair Kit. Could also be a failure of the power supply.
• HP 4/4+/5 most likely cause is burned out quartz lamp. Order the HP 4 Service 50 Error Repair Kit. Could also be a failure of the power supply.
• HP 4L/4P/5L/5P/6L/6P most likely cause is a bad ceramic heating element.
• All other printers most likely cause is burned out quartz lamp. In rare instances the ac power supply has failed. Even rarer, the DC controller is defective.


Error 51 (beam detect error)
• HP II/III series see tweaking page. Check the tab on the bottom of the toner cartridge facing you as you open the printer. If it's broken off it won't open the laser shutter. Check fiber optic cable for kinks or other damage.
• HP IIP/IIP+/IIIP could be either the laser pca or the scanner motor. Listen for erratic sounding scanner motor. There is a tab on the front of the toner cartridge that could also cause the problem. If its damaged or worn, it won't open the laser shutter. Check fiber optic cable for kinks or other damage.
• All other printers, replace laser scanner assembly.
Error 52 (scanner motor malfunction)
• HP II/III series see tweaking page.
• HP IIP/IIP+/IIIP order the 52 Service Error Repair Kit.
• All other printers, replace laser scanner assembly.
52.11.03 Service 4MPlus
• Cek bagian memory external
Error 53 (accessory memory error)
• All printers replace bad memory board or defective SIMM. See specials page.
Error 54
• Defective duplexer.
Error 55 (internal communication problem)
• On the HP 2 series you have to replace both the dc controller and formatter boards. On all other printers it can be several things: DC controller, formatter, main motor
Error 56
• On the IID/IIID the output selector knob on the rear assembly is not in the duplex position. On the IIISi/4Si a command was sent to print envelopes while the printer was in duplex mode.
Error 57
• 6L/5L Memory card incompatibility - 1,2,4,8 MB, 5 volt, 70 nanosecond or faster
• 6P/5P/5 Improper main motor function, check gear train for binding. Check DC controller connections - replace main motor
• 4L/4 Main motor problem, check gear train for binding. Replace main motor
• IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either in the top or bottom slot. Also check motor cable connections. Replace main motor. Can also be a defective DC controller.
• 5Si/4+/4Si/IIISi (X=2, 3 or 4) Fan motor is defective, check fan number X or duplexer fan and replace as necessary
• 5 Main motor failure - replace main motor
• 4+ 57.1 Gears are seized, main motor is bad or DC controller is bad
• 4Si/IIISi 57.1 Gears seized, defective top cover switch, faulty AC interlock switch, J010 loose or faulty, bad main motor PCA
Error 58
• 4/4L/4P/4V/5/5P Check the fan cable - reseat the cable or replace the fan
• 4V/4MV Defective DC controller board - replace dc controller
• 4Si/IIISi 58.1/58.2 Paper cassette is impoperly inserted
• 5Si 58.X Tray/Lifter Malfunction if X=1: Tray 2 lifter, X=2: Tray 3 lifter, X=3: Tray 1 lifter, X=4: Tray 4 lifter Press SELECT to continue
Error 59 Add Memory
• 4Si/IIISi Not enough memory for PostScript option. Verify SIMM's are seated properly, replace any defective SIMMS
• 5Si 59.X Main motor malfunciton X=1: Main motor startup failure, X=2: Main motor rotation failure Error 62.X
62.0 Service, 62.1-4 Service, 62.5 Service, 62.6 Service All Printers
• 1. Improperly seated SIMMs or font cartridge - remove, check and clean the contacts, re-install and try again.
• 2. Defective Internal Memory - Replace the Formatter PCA.

Error 67 Defective formatter PCA
• 2/2D/2P/2P+/3/3D/3P/4/4+/4P - Defective formatter board, try reseating the connectors and any accessories you may have plugged in to it, turn power off first!
• On the 4Si it could be a temporary error which can be corrected by cycling the power
• 4V/4MV - Most common cause is a defective paper guide plate assembly.
• 5Si The field replaceable units (FRU's) not installed correctly. Check and reinstall.
Error 79
• Software/drivers, Memory PCA's, Font-Macro-Personality Cartridges, option I/O Cards. Defective toner cartridge in the Laserjet 4 Plus only. Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again. If the problem persists and is application specific, verify proper setup with application vendor.
• Defective Formatter PCA - Replace with known operational board and try again.
Error 80
• Improper MIO connection - look at pins on formatter MIO connection
• Defective MIO Card - Replace card
• Defective Formatter Card - Replace card
4MPlus
• 1.Reset Bagian memory.
• 2.Copot Jetdyrect –kemudian hidupkan lalu pasang lagi.
Error 89
• The PostScript ROM's have bent or broken pins inspect the pins and reseat if necessary
• Check to see that the ROM SIMM's are in the proper location and oriented properly
• This can also be a temporay error, try power cycling the printer
• The PostScript ROM's/SIMM are defective

Read more...

Resetter Printer MP Series (MPTool)

Software yang satu ini adalah untuk mereset printer canon atau khusus printer canon MP series,yaitu

P150,MP160,MP170,MP180,MP145,MP460dan sejenisnya.
mengenai fasilitas dari software ini bisa dibilang lumayan banyak,bisa digunakan untuk mereset tinta baik yang hitam maupun yang warna, bisa untuk mereset waste ink counter,bisa juga untuk membackup eeprom printer bahkan untuk mengembalikan lagi file backup tersebut ke printer lain.
Untuk yang belum punya sowtware syang satu ini bisa anda download di bagian Link Download.
yang perlu anda perhatikan adalah waktu menggunakan software ini anda harus mengetahui, bahwa printer canon memiliki 3 mode kerja diantaranya: Mode Normal, Low Level Mode dan Service Mode.
untuk menggunakan software ini anda harus masuk di mode low level mode dan untuk masuk di mode tersebut anda harus melalui beberapa langkah:
* Matikan printer dan cabut kabel power.
* Tekan dan tahan tombol power printer.
* Sambungkan kabel power printer.
* Tekan dan lepas tombol resume.
* Kemudian lepas tombol power printer.
* Jikalau nanti printer terdeteksi dengan hardware lain, install drivernya terlebih dahulu.
OK semoga berhasil............

Read more...

HP Laser Printer error 13 - paper jam

ALL HP LASER PRINTERS
1. Out of spec media.
2. Pick up roller came out of place.
3.Paper cassettes not correctly loaded.
4. Dirty or obstructed paper path. Paper Jam in paper path.
5. Worn pick up rollers an separation pad.
6. Wrong length paper or incorrect software paper size selected.
7. Defective exit sensor.

8. Defective input sensor doesn?t sense paper out.
7. Paper cassettes not correctly loaded.
9. Bad solenoid operation.
10. Bad gear or gears in drive train.
11. Bad main motor or drive circuit.
12. Bad delivery mechanism or coupler gear to main drive.
13. Bad main motor drive circuitry.

HP LASER PRINTER 2, 2D, 3, 3D
1. Defective sensor cable.
2. Defective registration assembly.
3. Defective fuser.
4. Duplex paper path is obstructed or contains worn Components.
5. Misadjusted or bent switchback assembly.


HP LASER PRINTER 4L, 4P, 5P,6P
1. Printer rear door open.
2. Stuck or broken flags or sensors.
3. Paper fragment under oblique rollers.
4. Transfer roller guide not seated.
5. Bad fuser ass'y
6. Bad toner cartridge
7. Worn pick up roller and reg. ass'y block.


HP LASER PRINTER 4, 4+, 5
1. Rear door open.
2. Broken or missing cassette paper out sensor flag.
3. 500 sheet lower cassette not properly adjusted.
4. Check transfer roller to ensure it is seated properly.
5. Bad input sensor, fuser exit sensor or bad paper end Sensor.
6. Defective output rollers.
7. Paper stuck in paper path / In the input unite.


HP LASER PRINTER 4V, 4MV
1. Toner cartridge gears worn or damaged.
2. Paper path gears worn or damaged.
3. Defective DC controller PCA.
4. Defective registration guide.


HP LASER PRINTER 5000, 5100
1. Check paper loaded in paper tray properly.
2. Check the paper length adjuster.
3. Look at the transfer roller ass'y for proper adjustment.
4. Check the paper path in the printer. Also make sure the duplexer paper path.
5. Bad fuser ass'y. Replace or reseat the fuser.
6. Check for bad toner cartridge.
7.Check that all of the ass'y are seated and that all of the doors are closed.
8. Change maintenance kit


HP LASER PRINTER 5SI, 8000,8150
1. Toner cartridge gears worn or damaged.
2. Paper tray feed and separation roller's worn.
3.Paper misaligned in paper tray. Look at the length and width adjustment.
4. Bad input unite.
5. Bad fuser ass'y
6. External input device paper jam. Check all added devise like 2000 sheet feeder, Mail box bin, Duplexer , Envelope feeder. Unplug all external device and run test with just the printer.
7. Paper jammed up in the exit ass'y on the left side of printer.
8. Transfer roller ass'y out of place or broken.
9. If paper is jammed under toner cartridge change registration or toner cartridge.
10. Change maintenance kit .


HP LASER PRINTER 3SI, 4SI
1. No pick or media jammed in printer. Check the entire paper path of the printer.
2. Media in duplex. Check the duplexer paper path
3. Sensor malfunction.
4. Output sensor malfunction. Turn of offset ass'y in the 4si only
5. Check registration area fuser exit sensor flag and sensor.
6. Bad fuser ass'y
7. Worn feed and separation rollers.
8. Changed maintenance kit.


HP LASER PRINTER 5L, 6L, 3100, 3150
1. Paper not loaded in the paper bin.
2. Bad paper bin sensor.
3. Bad toner cartridge.
4. Bad fuser ass'y.
5. Worn pick up rollers and separation kit / Pulling multiple sheets threw printer.
6. Paper bin over full..


HP LASER PRINTER 1005, 1012, 1150, 1300
1.Check paper in the paper tray.
2. Worn pick up rollers and separation pad.
3. Bad shutter door on toner cartridges. Change toner cartridge.
4. Bad fuser ass'y.
5. Bad pick up roller shaft and clutch.


HP LASER PRINTER 1100, 3200 Fax, HP PRINTER 2100, 2200
1. Paper jam open paper trays make sure paper is loaded properly.
2. Make sure the paper length is adjusted in the 2200 series.
3. Paper jam check rear door and open and close top cover.
4. Paper jam check duplexer.
5. Paper jam internally / under the toner cartridge.
6. Worn pick up and separation pad.
7. Bad fuser ass'y .
8. Change maintenance kit .
9. Paper bin over full.


HP LASER PRINTER 1000, 1200, 1220mfp, 3300, 3300mfp
1. Check for paper loaded in paper tray properly.
2. Worn pick up roller and separation pad.
3. Feed roller shaft is bent or warped.
4. Paper stuck in paper path.
5. Bad fuser ass'y
6. Bad shutter on toner cartridge. Change toner cartridge.
7. Front door not properly shut.


Hp Laser Printer 2300
1. Check paper Path / Check paper trays
2. Check the length adjustment on the paper trays.
2. Check Duplexer
3. If jammed message persists after all jams have been cleared, a sensor might stuck or broken
4. If it keeps jamming need to change feed rollers and separation pad.
5. Bad fuser ass'y


HP LASER PRINTER 4000, 4050, 4100, 4100mfp
1. Ensure paper is loaded in paper tray property.
2. Check feed and separation rollers for unusual wear.
3. Check for the paper length adjusted in paper tray.
4. Bad fuser ass'y
5. Check paper path in duplexer.
6 Check small belt media roller to ensure that the roller and belt are feeding the media properly.
7. Check that transfer roller is seated properly.
8. Change maintenance kit


HP LASER PRINTER 4200, 4300
1. Check for paper loaded in paper tray properly.
2. Check for paper length adjusted in paper tray.
3. Check duplexer paper path.
4. Defective printer cartridge. Shutter door not opening all the way.
5. Look at feed and separation roller for wear or have popped off
6. Make sure no jam in stapler / stacker. Make sure to remove the staples and get the jammed stapled out.
7. Bad D.C. controller.
8. Change maintenance kit


HP LASER PRINTER 4500
1. Paper jam- check all rear doors.
2. Paper jam- check middle front drawer and duplex drawer.
3. Paper jam- check all drawers.
4. Paper or wrong media in fuser. Like a none Hp transparences that melted in fuser ass'y
5. Worn feed and separation rollers.
6. Bad middle drawer ass'y.
7. Bad fuser ass'y


HP LASER PRINTER 8500
1. Paper jam internally.
2. Check paper trays for missed loaded paper.
3. Paper jam- check all doors.
4. Paper jam- check duplexer.
5. Paper jam- check mailbox bin.
6. Bad fuser ass'y.


HP LASER PRINTER 9000
1. Paper jam- check trays, all doors, paper path.
2. Paper jam- check duplexer.
3. Paper jam- internally.
4. Check doors to make sure they are closed.
5. Make sure all feed and separation rollers are properly installed.
6. If paper stops before fuser check the transfer ass'y or change it.
7. check fuser ass'y for paper stopping at the fuser. Bad fuser change it.
8. Bad D.C. controller
9. Paper is jammed at exit ass'y changed the delivery ass'y
10. Replaced the diverter if the paper still doesn't make out of exit.
11. Replace the flipper ass'y
12. Replace the accumulator ass'y.
13. Check all device on printer. Run test with one device taken off one at a time.
14. Change maintenance kit

Read more...

HP Maintenance Message Reset Methods

To clear the Maintenance Service Message from the LCD display:

HP IIISi Printers:

Press ONLINE until the light goes off
Hold down MENU until PCL CONFIG MENU appears
Press the MENU key until SERVICE MSG=ON* appears
Press the + or - key to change display to SERVICE MSG=OFF
Press ENTER/RESET MENU key to turn message off, the * should appear, then press ONLINE

HP 4Si Printers:

Press ONLINE until the light goes off
Press MENU until CONFIG MENU appears
Press the ITEM key until SERVICE MSG=ON* appears
Press the + or - key to change display to SERVICE MSG=OFF
Press the ENTER key to turn message off, the * should appear, then press ONLINE

HP 5Si:

Press MENU key 4 times for CONFIG MENU
Press ITEM to display SERVICE MESSAGE=OFF
Press ENTER
Press ONLINE




HP 4000/4050/4100/5000 Printers:

Turn the printer off
Hold down the left side of the ITEM and VALUE +/- keys, turn the printer on and wait until RESET MAINTENANCE COUNT is displayed and then release the keys




HP 4500/4550 Printers:

Turn the printer off
Hold down the CANCEL JOB and SELECT keys and turn the printer on, then wait until the display goes blank and the three LED's come on
Press the right side of the MENU key, then press the SELECT key
You will enter SERVICE MODE after the normal test completes
Press the ITEM key until the FUSER MAINTENANCE COUNT appears
Press VALUE +/- to change to zero
Press SELECT to save
Press GO; the printer should return to READY




HP 8000/8100/8150 Printers:

Press the MENU button until the display reads CONFIGURATION MENU
Press the ITEM button until the display reads SERVICE MESSAGE = ON/OFF
Select OFF*
Press SELECT to save
Turn printer off
Hold the VALUE MINUS and ITEM MINUS buttons while turning the printer back on Hold buttons down until display reads RESET MAINT/COUNTand then release both buttons




HP 9000 Printers:

Turn the printer off
Press and hold the CHECK key
Power on the printer
Release the CHECK key after all three lights come on The display should read SELECT LANGUAGE
Press the up arrow until MAINTENANCE KIT is displayed, then press the CHECK key again and the maintenance kit count has been reset




HP Color LaserJet 4500/4550 Printers (TRANSFER KIT RESET):

Press the MENU button until the RESETS MENU is displayed
Press the ITEM button until TRANSFER KIT SELECT IF DONE is displayed
Press the SELECT button




HP Color LaserJet 4500/4550 Printers (FUSER KIT RESET):

Press the MENU button until the RESETS MENU is displayed
Press the ITEM buton until FUSER KIT SELECT IF DONE is displayed
Press the SELECT button
Press the GO button to return to READY




HP Color LaserJet 4600 Printer (IMAGE TRANSFER KIT (ETB) RESET):

After Maintenance is performed, the display should read NEW TRANSFER KIT =
Press the down arrow to highlight YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW TRANSFER KIT and select




HP Color LaserJet 4600 Printer (FUSER KIT RESET):

After Maintenance is performed, the display should read NEW FUSER KIT =
Press the down arrow to highlight YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW FUSER KIT and select




HP Color LaserJet 8500/8550 Printers (TRANSFER KIT RESET):

Press the MENU button until the RESETS MENU is displayed
Press the ITEM button until RESET TRANSFER LIFE COUNT is displayed
Press the SELECT button to reset, then GO to return to READY



HP Color LaserJet 8500/8550 Printers (FUSER KIT RESET):

Press the MENU button until the RESETS MENU is displayed
Press the ITEM buton until RESET FUSER LIFE COUNT is displayed
Press the SELECT button to reset
Press the GO button to return to READY

Read more...

Canon GENERIC "PIXMA MP" SERIES RESET CODE

PRINTER PIXMA MP 150

1. With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2. When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3. When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4. When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in. (orange and green, starting with orange.)

The number of the Reset
button pressing

LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset procedures below.
5 times Orange Destination setting See Destination setting procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection


mpc190/200
Resetting the Waste Ink Volume Counter
1) Enter SERVICE MODE.---
By pressing Menu-Copy-Scan-Copy-Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [OK] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.


mpc730
Resetting the Waste Ink Volume Counter
1) Enter SERVICE MODE.---
By pressing Menu-Copy-#
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [OK] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.



I followed your provided key sequence and was able to reset the "Check Printer" alarm in my MultiPass F30 printer. It is very close. The only thing is that there is no [OK] key on the F30 printer. I had to press [ON/OFF] key instead. After the waste tank full counter was reset, my printer works normally again.

I also have a MultiPass MP700 printer. I am sure that the key sequence will come in handy someday. Similarly, there is no [OK] key on the MultiPass MP700 printer.







Canon MPC190
Reset Waste Ink
1) Enter SERVICE MODE.
By pressing Menu Copy Scan Copy Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

The reset procedure (for canon MP130/MP110) is:-
Turn on the machine
(1) Press MENU
(2) Press SCAN COPY SCAN to enter service mode
(3) USE > to got to NVRAM ACCESS
(4) set ABS-M LEVEL to 0
(5) set ABS-P LEVEL to 0
(6) Press STOP to EXIT
DONE !

Mpc 400 - the 343 problem solution
Hi there, after a relatively long journey through the net i finally have found the solution ;-) these are the steps for canon mpc 400 error ##343:
1. Go to menu by pressing the > button
2. press [copy] and then #
3. go to 'test mode' by pressing > several times
4. now press 8 then 3 then 0
5. After that press the on/off button, everything should be fine now.




Canon Seri MP700

> Replace all the Ink Absorbers.
> QA4-1012-000
> QA4-1013-000
> QA4-1014-000
> QA4-1015-000
> QA4-1055-000
> Reset the counter to zero.

Prosedur reset counter :

1. Pencet tombol "menu"
2. Pencet tombol "Copy"
3. Pencet tombol "#"
4. Scroll menu sampai muncul tulisan "Test Mode" / menu ke-12
5. Pencet tombol "3" untuk menghapus Eeprom
6. Pencet tombol "0"
7. Pencet tombol "Stop"

Untuk seri mpc190/200

Prosedur reset counter :

1) Enter SERVICE MODE.---
By pressing Menu-Copy-Scan-Copy-Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [OK] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Read more...

Canon GENERIC "PIXMA" SERIES RESET CODE

Pixma ip 2000 waste ink counter reset:
Service Mode Operations
1) With the printer powered off, hold down the resume button and press the power button.
2) While holding down the power button, release the resume button and press the resume button twice in succession. Now release the power button. The indicator will blink in green and remain lit in green.
3) Select one of the following service mode functions by pressing the resume button the specified number of times.
Press Resume Indicator Functions
4 times Green Waste ink counter resetting

Canon PIXMA iP1000
Waste Ink Counter Reset Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

Canon PIXMA iP1500
Waste Ink Counter Reset. Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.)
should be orange.
5. Press and release the RESUME button again, the indicator
(L.E.D.) should be green
6. Release both buttons

Here's the ip4200 reset options:
1) With the printer power turned off, while pressing
the Resume/Cancel button, press and hold the Power
button. (DO NOT release the buttons. The Power LED
lights in green to indicate that a function is
selectable.)
2) While holding the Power button, release the
resume/Cancel button. (DO NOT release the Power
button.)
3) While holding the Power button, press the
Resume/Cancel button 2 times, and then release both
the Power and Resume/Cancel buttons. (Each time the

Resume/Cancel button is pressed, the Alarm and
Power LEDs light alternately, Alarm in orange and Power
in green, starting with Alarm LED.)
4) When the Power LED lights in green, press the
Resume/Cancel button the specified number of
time(s)
setting).
Time(s) LED indication Function Remarks
0 times Green (Power) Power off When the print head is
not installed, the carriage returns and locks in the

home position capped.
1 time Orange (Alarm) Service test print .
2 times Green (Power) EEPROM information print
3 times Orange (Alarm) EEPROM initialization
4 times Green (Power) Waste ink counter resetting
5 times Orange (Alarm) Destination settings After
entering the destination settings mode, press the
Resume/Cancel button the specified number of time(s)

to select the destination. For detail, see
"Destination settings procedures" below.
6 times Green (Power) Print head deep cleaning
(Cleaning of both black and color)
7 times Orange (Alarm) Reserved
8 times Green (Power) CD / DVD check pattern
9 times Orange (Alarm) CD / DVD print position
correction (horizontal: X direction)
10 times Green (Power) CD / DVD print position
correction (vertical: Y direction)
11 to 13 times Orange, Green, Orange(Alarm,
Power,Alarm) Return to the menu selection
14 times Green (Power) Left margin correction Not used

in servicing.
15 times Orange (Alarm) Return to the menu selection


Time(s) LED indication Destination CD / DVD print
0 times Green (Power) No change of the destination
1 time Orange (Alarm) Japan Supported
2 times Green (Power) Korea Not supported
3 times Orange (Alarm) US Not supported
4 times Green (Power) Europe Supported
5 times Orange (Alarm) Australia Supported

Read more...

Canon GENERIC "S & i" SERIES RESET CODE

i320 waste ink counter reset.
1. Turn off the printer.
2. Press and hold the POWER button, turn on the printer.
3. The indicator should be green.
3. Press and release the RESUME button , the indicator should be orange.
4. Press and release the RESUME button again, the indicator should be green.
5. Release both buttons.
6.Connect the printer to PC.
7.Open General Tool software,choose ¡°USB PORT¡±.
8.Choose ¡°SET DESTINATION 1 ¡±,OK!


Canon i550, i560, i850, i950, i960 (May work with i860, i865)

1. Start with the printer OFF
2. Hold down RESUME and then hold down POWER
3. release RESUME
4. press RESUME twice, then release POWER
5. Let green light blink until printer is done moving print head.
6. Select functions below with RESUME press POWER to execute:
Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

i250, i350 and i000 series
1: Unplug power and USB
2: Open door and hold power button.
3: Connect power.
4: Close door, then release power button
5: Connect USB and an press power to use.
This method will work only whilst the printer's connected to power. Turning off and on at the switch will keep it, but unplugging it from the power will reset it, which means you'll have to do this again: What this does is temporarily reset the printer, but also stops it from doing headcleans everytime you open the door to switch print heads or ink tanks.



GENERIC “S” SERIES RESET CODE.
This reset is an emailed submission. But the person who sent it in requested their name to be withheld.
This reset is for the S series printers. This does look like the same reset for the S9000 but has a little more detail.
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in succession. Note:

you are still holding the POWER button). The printer's carriage will “reset" or move momentarily.
If the above was properly performed the printer will enter the "Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM – Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point – However it is best leave them unaltered – You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the
function selection menu. Press the POWER button again to restart the printer.

Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal


Canon i550, i560, i850, i950, i960 (May work with i860, i865)
1. Start with the printer OFF
2. Hold down RESUME and then hold down POWER
3. release RESUME
4. press RESUME twice, then release POWER
5. Let green light blink until printer is done moving print head.
6. Select functions below with RESUME press POWER to execute:

Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

Waste Ink Tank Reset - i-series


1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal

Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

Canon i320, i255
Waste Ink Counter Reset.
Step 1 : Manual Temporary
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
or Step 1: Manual Temporary
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

Canon i850, i950, S600
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter



Canon S450 Printer
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
7: Press Power to set data

Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA IP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Canon S900, S820, S750, S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.
The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.

1. Service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.



Canon S9000
Turn off printer
Hold down Resume button and press Power button.
Keep holding down Power button and let Resume button go.
Press Resume button 2 times then let BOTH buttons go.
Green lights will flash and then stop blinking.
When green lights are solid, press the Resume button 4 times.
Press the Power button and the printer should turn off, if not, press the Power button once more.
Your printer should respond as normal.

Read more...

Canon GENERIC "BJC" SERIES RESET CODE

Reset code for the BJC 1000.
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

Canon BJC-3000 waste ink tank full

Give this reset a try:
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data

The waste-ink counter for the BJ F900, F890, F700, F500, S900, S820, S750 and S520 are all reset in the same manner.
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.
If you have a defective printer head, your power lamp may flash during the service mode key-in, and info printouts may not work. In this case, clearing the waste-ink counter may not fix your problem.
Here's a Reset Procedure ... The problem was if error occured the unit would halt further activity so printing was suspended ... the particular error was the photo ink tank was empty and it took awhile to select everything so I could print with Black only ... photo ink error needed clearing ...

Canon BJC-8000 Overall Reset Procedure (No paper in tray) to clear errors etc
1. Disconnect powercord, Hold Down Power and Resume Buttons
2. Connect the powercord and unit will turn on
3. Release Power Button, then click it once
4. Release both Power and Resume Buttons
5. Green Power light will be on steady, amber Resume light went off
6. Then at about 1 second intervals ... click Resume, click Resume, then click Power...In a few seconds Startup Cycle Machinations will occur and finish
7. Do a Button Power off ... a Button Power on wont work ...
unplug then replug power ... Button Power on / off , Machinations OK,
error cleared now

Here's a waste error reset from a U.K. site for a Canon BJC-8000 ...
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data.


My S520 gives also the well known waste tank full indication (7 times orange), so i,ve tried
the reset from "Chimp says", but that doesn,t work.
What is going wrong.
First must i do this whit the lid open or closed ?
I,ve done the following:
1. turn off the printer (with the powerswitch)
2. press the resume button, and press the Powerswitch.
3. release the resume button and then press it twice short after each other.
4.Then release the Power and the Resume switch,
now the orange light keeps flashing.
5. I then pressed the Resume button 4 times.
6. Then I,ve pressed the power switch 1 time.
7. at last i,ve shut off the power using the powerswitch.
Result nothing happened....
I have also tried to shut off the power by disconnecting the powercable.
Can anyone here give me some advice please ?
greetings Henk

Canon BJC 1000 Serie
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

Canon BJC-2000 BJC-2100 Serie
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
3: Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.


Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
Unplug Power Cord
Hold POWER and RESUME buttons
Plug in Power Cord
Release buttons
Open front door of printer
Hold the CARTRIDGE and RESUME buttons
Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME

Canon BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.


Canon BJC-5100
Self Test
Switch Printer off. Hold Power for 1 beep.

Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500

1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data

Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps

Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord


Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer


Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a resta

Read more...

HP LaserJet family printer error codes.

Error 02 Warming up

• Turn printer off.
• Unplug I/O cable from rear of printer.
• Power up printer and see if it goes to ready.
• If printer goes to ready, the problem could be a driver issue, a bad I/O port in the computer or a bad I/O cable.
• If the printer still stays in 02 warm up, replace the formatter board.

Error 11 Paper Out
• Check paper tray for paper. Make sure it is seated properly.
• Check the tray size actuating tabs on the paper tray for damage. Check to see if the actuators they contact aren't bent. The micro-switches they actuate could be defective or misaligned. Manually depress the actuators and listen for a click.
• Check that the paper sensor arm isn't stuck or broken.
• Paper Control Sensor PCA is defective.

Error 12 Printer Open no EP cartridge
• Check that the toner cartridge is installed.
• Check that the top cover is firmly closed.
• On HP II/IID/III/IIID printers this error is usually caused by a bad DC power supply.
• On HP IIP/IIP+/IIIP printers the primary cause is the density density adjusting. There is a slight possibility of it being a bad fan. There is also a slight possibility of the tab on the fuser access door above the MP tray breaking off and causing the error. If the fan starts to run, quits and you notice a burning odor, the scanner motor has failed and needs to be replaced. The problem can also be caused by a defective drum shutter on the toner cartridge.
• On the 4/4M/4+/4M+ the tab on the top cover that actuates the door interlock could be broken.

Error 13 Paper Jam
• Paper jams can occur in 3 places: Entry, registration and exit.
• If the paper isn't picking up out of the paper tray, visually inspect the pickup roller. If it looks shiny, replace it. You should also replace the separation pad as they work together. On the 4L/4P/5P/6P the pickup roller has a plastic shaft that breaks. You'll have to replace the whole pickup assembly. This requires major disassembly of the printer. Check our printer repair kits for your model printer. If you don't see it listed, email us.
• If you have an HP 4/4+/5 with an optional 500 sheet feeder that's jamming, check the balance knob adjustment. Center it with a full ream of paper for proper operation.
• If the paper is jamming at registration or anywhere between pickup and exit it could be a number of things. Check the paper path for torn bits of paper or label residue. On the II/III series, remove the metal registration guide plate (2 screws) and check underneath it. If the pickup rollers are moderately worn, the paper will stop just short of the registration roller. On the 4L/4P/5P/6P remove the screw holding the oblique roller assembly (Inside front of printer) and pull out and inspect the assembly and the area under it. On the HP 4/4+/5 pivot up the metal plate and check underneath it. Check the roller assembly on the left side for torn scraps of paper (a flashlight or torch is necessary).
• Make sure paper cassettes are firmly seated, corner tabs aren't bent. Some trays have lifting springs that could pop out if tray has been dropped.
• On HP IIP/IIP+/IIIP printers if the paper scrunches up at the toner cartridge you'll need our Inside Accordion Jam Repair Kit.
• Check your software settings in the program you are attempting to print from. Do you have the correct paper size specified? If you have a different paper size than what is in the tray, you'll get a paper jam.
• Exit jams are frequently caused by exit sensors. These sensors are typically mounted on the fuser assembly or adjacent to it. They are plastic arms that block and unblock an optical sensor. The arms can get stuck or knocked out of place when clearing paper jams. The optical sensors can also get dirt blocking the photo cell. Clean the sensor and check for free movement and proper installation of the sensor arms.
• On HP II/III series exit jams are mostly caused by worn gears. The best way to troubleshoot this is to defeat the door interlock. Press down on the arm on the top right of the fuser. Initiate a test page. While holding down the arm, press one of the metal cartridge detect switches just below the door interlock. Watch the movement of the gears. You will get a 51 error because the door is open. Recycle power to get rid of error. There is an arm gear on the lower right of the fuser that can shed teeth. There is also a 14 tooth gear below the large gear on top of the fuser. You can also manually rotate the large gear and check for binding or crunching. If that happens, then replace the 14 tooth gear. On the door, there are some delivery coupler gears that mate with the fuser and drive the exit roller. Check the gears for excessive wear. Replace if necessary. If the paper gets almost all the way out and jams, replace the exit roller or the exit roller assembly. If the error occurs after fuser replacement, check and see if the connector on the left of the fuser is properly mated with the one in the printer.
• On HP IIP/IIP+/IIIP printers if the paper has accordion folds on the bottom and jams on exit, order our Top Output Accordion Jam Repair Kit.
• On HP 4/4+/5 printers the most common cause of exit jams is the exit assembly. Order our 4/4+/5 Exit Jam Repair Kit. Exit jams in the fuser can be caused by a broken fuser drive gear or a broken gear on the fuser. Remove the fuser and check the gear inside the printer for broken teeth. Manually turn the gears on the fuser and check for smooth operation. Check the paper exit sensor arm for proper mounting and free movement.
• Check to make sure the rear door is closed on the printer. Open doors can cause 13 paper jam indications.
• On the 5L/6L check the registration sensor arm below the pickup roller. Also check the exit sensor arm (bottom center of the fuser). These arms frequently get stuck or dislodged clearing paper jams. On these printers, if you are experiencing frequent paper jams, order our 5L/6L Multi-Sheet/No Feed Repair Kit
Error 14 No EP cartridge
• Check that a toner cartridge is installed and fully seated.
• On HP II/III and IISi/4Si models check that at least one sensitivity tab is installed on the right side of the toner cartridge. If you see 2 holes and no square plastic tabs sticking in at least one of them, the printer will not see the cartridge. If one tab is installed and the printer still doesn't recognize the cartridge, try popping out the tab and putting it in the other position.
• On HP 4/4+/5 printers the high voltage contacts can be dirty or misaligned. If contacts are ok, replace the high voltage power supply.
Error 16 Toner low
• Toner cartridge is low on toner. Try gently rocking the cartridge to redistribute the toner. This will buy you 50-100 pages. Get a new cartridge as soon as possible.
• Dirty or misaligned contacts on the high voltage power supply.
• On the HP II/III printers it can be a loose connector on DC controller see tweaking for instructions on how to repair it.
• On the HP 4/4+/5 printers there is a potentiometer adjustment on the left side of the printer. You have to remove the left panel and you'll see it. It's located at about the exact center of the printer.

Error 18 MIO Not Ready
• The printer is not connected to a Lan.
• The MIO (Jet Direct) card is defective or not seated correctly. Reseat or replace it. If you have another printer with the same card, try swapping them. Always turn printer power off when removing or inserting cards.

Error 20 Memory Overflow
• Print job has exceeded the memory capacity of the printer. Simplify the print job, reduce the dpi setting or install additional memory. See our specials page for memory.
Error 21 Print Overrun
• See error 20

Error 22 I/O Configuration
• Printer or computer I/O configuration is incorrect
• I/O cable is wrong or damaged
• The computer is switched off
• I/O port on printer is damaged. Replace the formatter.

Error 23 I/O Not Ready
• I/O card can't accept data or isn't connected to the network. Check card seating (with power off) and replace if necessary.

Error 24 Job Memory Full
• Too much data or too complex data for printer memory. See error 20.

Error 25 XXX Memory Full
• Too much data or too complex data for printer memory. See error 20.

Error 30 PS Error 16
• I/O time out. Printer got tired of waiting for user interaction like a manual feed. Check the I/O connections. Check display panel for media request.

Error 30 PS Error 22/25
• Postscript error. Replace the Postscript SIMM module

Error 30 PS Error (all others)
• A PCL file was sent to the printer while it was in Postscript mode.
Error 30.1.1 Disk Failure
• 5si/8000 optional hard drive has crashed. Press select to continue.

Error 40 Data Transfer Error
• Printer and computer may be set to different baud rates.
• The computer is turned off.
• The MIO card is defective or improperly seated.
• Press continue or go on the printer to clear message.

Error 41 (temporary print engine error)
• Temporary error has occurred. Press Go or Continue. Power cycle the printer.
• On IIP/IIP+/IIIP with lower cassette option order our 41 Service Error Repair Kit

Error 41.1 41.2 41.3
• Defective connections. Reseat J205,206,207 and laser scanner connectors.
• Paper multifeed or wrong size paper being used.
• Paper size selection doesn't match the paper being used.
• Cassette is overfull or improperly adjusted.

Error 41.4 or 41.5
• Formatter PCA or DC controller is defective.

Error 50 (fuser malfunction)
• HP II/III series most likely cause is the ac power module is defective. Order the HP II/III Service 50 Error Repair Kit. If the quartz fuser lamp is burned out, order the replacement fuser on specials page. Slight possibility of loose connector on DC controller. See tweaking page DC controller could also be defective, but this is very rare.
• HP IIP/IIP+/IIIP most likely cause is burned out quartz lamp. Order the HP IIP/IIIP 50 Service Error Repair Kit. Could also be a failure of the power supply.
• HP 4/4+/5 most likely cause is burned out quartz lamp. Order the HP 4 Service 50 Error Repair Kit. Could also be a failure of the power supply.
• HP 4L/4P/5L/5P/6L/6P most likely cause is a bad ceramic heating element.
• All other printers most likely cause is burned out quartz lamp. In rare instances the ac power supply has failed. Even rarer, the DC controller is defective.

Error 51 (beam detect error)
• HP II/III series see tweaking page. Check the tab on the bottom of the toner cartridge facing you as you open the printer. If it's broken off it won't open the laser shutter. Check fiber optic cable for kinks or other damage.
• HP IIP/IIP+/IIIP could be either the laser pca or the scanner motor. Listen for erratic sounding scanner motor. There is a tab on the front of the toner cartridge that could also cause the problem. If its damaged or worn, it won't open the laser shutter. Check fiber optic cable for kinks or other damage.
• All other printers, replace laser scanner assembly.
Error 52 (scanner motor malfunction)
• HP II/III series see tweaking page.
• HP IIP/IIP+/IIIP order the 52 Service Error Repair Kit.
• All other printers, replace laser scanner assembly.
52.11.03 Service 4MPlus
• Cek bagian memory external

Error 53 (accessory memory error)
• All printers replace bad memory board or defective SIMM. See specials page.

Error 54
• Defective duplexer.

Error 55 (internal communication problem)
• On the HP 2 series you have to replace both the dc controller and formatter boards. On all other printers it can be several things: DC controller, formatter, main motor

Error 56
• On the IID/IIID the output selector knob on the rear assembly is not in the duplex position. On the IIISi/4Si a command was sent to print envelopes while the printer was in duplex mode.

Error 57
• 6L/5L Memory card incompatibility - 1,2,4,8 MB, 5 volt, 70 nanosecond or faster
• 6P/5P/5 Improper main motor function, check gear train for binding. Check DC controller connections - replace main motor
• 4L/4 Main motor problem, check gear train for binding. Replace main motor
• IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either in the top or bottom slot. Also check motor cable connections. Replace main motor. Can also be a defective DC controller.
• 5Si/4+/4Si/IIISi (X=2, 3 or 4) Fan motor is defective, check fan number X or duplexer fan and replace as necessary
• 5 Main motor failure - replace main motor
• 4+ 57.1 Gears are seized, main motor is bad or DC controller is bad
• 4Si/IIISi 57.1 Gears seized, defective top cover switch, faulty AC interlock switch, J010 loose or faulty, bad main motor PCA

Error 58
• 4/4L/4P/4V/5/5P Check the fan cable - reseat the cable or replace the fan
• 4V/4MV Defective DC controller board - replace dc controller
• 4Si/IIISi 58.1/58.2 Paper cassette is impoperly inserted
• 5Si 58.X Tray/Lifter Malfunction if X=1: Tray 2 lifter, X=2: Tray 3 lifter, X=3: Tray 1 lifter, X=4: Tray 4 lifter Press SELECT to continue

Error 59 Add Memory
• 4Si/IIISi Not enough memory for PostScript option. Verify SIMM's are seated properly, replace any defective SIMMS
• 5Si 59.X Main motor malfunciton X=1: Main motor startup failure, X=2: Main motor rotation failure Error 62.X
62.0 Service, 62.1-4 Service, 62.5 Service, 62.6 Service All Printers
• 1. Improperly seated SIMMs or font cartridge - remove, check and clean the contacts, re-install and try again.
• 2. Defective Internal Memory - Replace the Formatter PCA.

Error 67 Defective formatter PCA
• 2/2D/2P/2P+/3/3D/3P/4/4+/4P - Defective formatter board, try reseating the connectors and any accessories you may have plugged in to it, turn power off first!
• On the 4Si it could be a temporary error which can be corrected by cycling the power
• 4V/4MV - Most common cause is a defective paper guide plate assembly.
• 5Si The field replaceable units (FRU's) not installed correctly. Check and reinstall.
Error 79
• Software/drivers, Memory PCA's, Font-Macro-Personality Cartridges, option I/O Cards. Defective toner cartridge in the Laserjet 4 Plus only. Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again. If the problem persists and is application specific, verify proper setup with application vendor.
• Defective Formatter PCA - Replace with known operational board and try again.

Error 80
• Improper MIO connection - look at pins on formatter MIO connection
• Defective MIO Card - Replace card
• Defective Formatter Card - Replace card
4MPlus
• 1.Reset Bagian memory.
• 2.Copot Jetdyrect –kemudian hidupkan lalu pasang lagi.

Error 89
• The PostScript ROM's have bent or broken pins inspect the pins and reseat if necessary
• Check to see that the ROM SIMM's are in the proper location and oriented properly
• This can also be a temporay error, try power cycling the printer
• The PostScript ROM's/SIMM are defective

Read more...